Search results
If installing a threaded tub spout, connect to the valve with 1/2 inch pipe or 1/2 inch copper tubing with a threaded adapter. If installing a slip-fit tub spout, connect to the valve with only copper tubing – no threaded adapter is needed. See step 4.3 for tub spout tube length. Shower Only.
- 7MB
- 36
This video show how to install a Moen posi temp valve. This is a Moen 1/2 Inch PEX Posi-Temp Pressure Balancing Rough-In Valve. I will solder 2 fittings on...
- 12 min
- 39.6K
- Home Repair Hub
How-To Videos for kitchen & bath faucets, tub & shower fixtures, faucet cartridges, garbage disposals, and other Moen products.
Sep 17, 2019 · This video shares a Moen shower valve installation inside a tub shower. There are tips for soldering copper to the valve, using PEX, and more. For more home ...
- 4 min
- 374.9K
- Home Repair Tutor
- Disassembly
- UP HANDLE SERVICE KIT Reassembly
- TO REMOVE STOP VALVE
- Removal of stop valve:
- Re-Installation of new stop valve:
- Trim
- I.P.S.
- (Continued from page 3)
- Cleaning & Care Instructions for Special Finish Models:
- (800) BUY - MOEN (289-6636)
Turn "OFF" both hot and cold water supplies, then open faucet to relieve pressure. Remove handle cover from handle knob. Take out handle screw and remove handle knob, washer, and stop tube. Lift out retainer clip. Rotate cartridge shell back and forth with Moen cartridge twist wrench, grasp the cartridge stem with pliers, and pull out the cartr...
RUBBER STOP VALVE Re-insert cartridge by pushing it all the way into the body until the front of the ears on the cartridge shell are flush and aligned with the body, (see illustration). Replace the retainer clip so that the legs straddle the cartridge ears and slide down into the bottom slot in the body. This prevents the cartridge from rotating ...
Always turn water supply OFF before disassembly. Open faucet to alleviate sustained pressure.
Remove knob and escutcheon (pry off handle cap and remove handle screw). Using snap ring pliers, remove retaining ring from valve body. Grip stop valve stem with pliers and rotate slightly to remove from valve body.
Check to be sure that stop valve stem is fully seated in plug. Insert stop valve until fully seated beyond retaining ring groove in valve body. Using snap ring pliers, place retaining ring in valve body, making sure that ring is fully seated. Check orientation of stop valve for water flow. (Stop is in the off position when screwdriver slot is verti...
MAKE SURE ALL WATER SUPPLIES ARE OFF. SHOWER: Install flange on long end of arm. Wrap threads on both ends of shower arm with thread seal tape. Screw long end of shower arm into wall. Install showerhead. C.C. SPOUT: The Moen Slip Fit spout is designed with an O-ring seal. It is specifically designed for installation with copper water tube. L...
ESCUTCHEON SCREWS (2) C.C. CLAMP SCREW I.P.S. ESCUTCHEON TUB LOOKOUT NIPPLE I.P.S. TUB SPOUT IPS SPOUT: CAUTION: C.C. This spout is A.B.S. plastic and will crack when in contact with some pipe thread compounds. Please read the pipe compound label to be certain. We recommend using thread seal tape thread sealant. Screw tub spout onto pipe an...
ESCUTCHEON: Remove screw holding plaster ground in place. Discard plaster ground. Temporarily install handle knob or lever. Turn on water and check system for leaks. If there are no leaks, turn OFF water and remove handle knob or lever. Install escutcheon plate with two screws provided Mount with the notch UP. Install stop tube. The notche...
All that is necessary to clean these faucets is to wipe them with a soft, damp cloth such as terrycloth. Warm water will remove dry water spots. CAUTION: DO NOT use cleansers which contain abrasives or harsh chemicals. NEVER use alcohol or other organic solvents. A high quality, non-abrasive wax polish applied occasionally, will help to preserve...
for answers to any product, installation, replacement parts, or warranty questions.
- 198KB
- 4
Dec 15, 2021 · Before installing the U by Moen Smart Shower system, it’s important to consider a few key factors such as the number of shower outlets the homeowner intends to use in the shower, valve placement, location of a usable electrical outlet and strength of WiFi signal.
Care Instructions. To preserve the finish on the metallic parts of your Moen faucet, apply non-abrasive wax, such as car wax. Any cleaners should be rinsed off immediately. 6. Post Installation - Troubleshooting Guide. Problem. Hot/cold reversed. No water/low flow. Leak or drip from spout. Only hot/no cold – Only cold/no hot.
