Search results
theyellowcapecod.com
- In generic terms, today’s crown molding is any horizontal trim that separates the walls from the ceiling or adorns the tops of other architectural elements, such as door casings and cabinets. More specifically, crown molding is the term for a particular trim shape contoured to fit at an angle between the wall and ceiling.
www.bobvila.com › articles › crown-molding
People also ask
What is crown molding?
How does wood crown molding work?
Why do you need crown molding?
What is the difference between crown molding and ceiling molding?
Mar 9, 2021 · In generic terms, today’s crown molding is any horizontal trim that separates the walls from the ceiling or adorns the tops of other architectural elements, such as door...
Mar 12, 2013 · So this last weekend was a busy one as we purchased, cut, installed, caulked and primed crown molding in the living room! Today we’re going to discuss the basics of crown molding, with an emphasis on the inside corner joints. Tomorrow, we’ll discuss the outside corner joints! Let’s get started – WAIT!
- Every Crown Gets Backing
- Plan The Installation to Avoid Double-Coping
- Pinch Sticks Make For Easy, Accurate Measurements
- Outside Miters Must Fit Precisely
- Dual Compound-Miter Saw Makes Cutting Crown Less Confusing
- Two Tips to Make The Job Go Smoothly
- Coping Inside Corners
- Outside Corners Are Simple…
- …Unless They Aren’T Square
- What to Do When The Wall Is Longer Than The Stock
Even when I’m following a first-rate framing crew, experience has taught me to check every corner with a framing square and to note any serious irregularities. (A gap between the square and the wall corner of even 1 ⁄8 in. can make it difficult to close the joint on a large piece of hardwood crown). At the same time, I eyeball the wall and ceiling ...
Before I start chopping up the molding, I scope out the installation order. To avoid coping two ends of the same piece of molding and to eliminate the time and fuss of resetting my saw for each cut, I try to set up all my copes on the same end of each piece. Most right-handers find it easier to cope right, butt left. The direction doesn’t matter as...
Because joint compound tends to build up in the corners, it’s hard to get an accurate measurement by bending a tape measure into a corner. For long lengths of crown, I add a heavy 1⁄16 in. to all my measurements; then I put a slight back-cut on the square end. That way, even if the piece of crown is slightly long, it can be sprung into place, and t...
If the corner is crisp and square, I measure the length for an outside miter by holding the stock in place and marking the bottom edge of the molding where it meets the outside corner. (Bear in mind that drywall corner bead pushes the corner out slightly, so you may have to back-plane the miter to get a tight fit.) Plaster corners may be rounded sl...
If there’s any secret to cutting crown, it’s simply this: Keep track of which edge of the molding is the bottom and which edge is the top. Doing so eliminates a lot of head scratching when you’re standing at the saw trying to remember how the molding will sit when actually nailed into place. I try to group similar cuts together. That is, I first cu...
Backing the crown means you never have to search for a stud. Framing lumber ripped to match the spring angle of the crown provides continuous nailing for the molding. A framing square and a scrap of crown determine the backer dimensions. After ripping the material on a tablesaw, the author uses 3-in. screws to attach the backer to the framing. Inst...
It’s possible to assemble inside corners with a miter. However, even if the corner is perfectly square, most miter joints open after a few seasons of expansion and contraction. I prefer to cope crown molding. A coped joint is a marriage of opposites. On one side, the molding is cut square and butts tight to the wall. On the other side, the molding ...
Marking the long point is generally more accurate than marking the short point. To establish the long point of an outside miter, trace the top edge of a scrap of crown onto the ceiling, on both sides of the corner, then measure to the intersection of the two.
When I encounter an obtuse or acute angle corner, I use a couple of sticks and a bevel board to measure the exact miter angle. The bevel board is nothing more than a square piece of wood with some carefully drawn angled lines (from 0° to 90°). I made mine using a simple protractor and a sharp pencil. To get the exact bevel angle for an out-of-squar...
If a wall is longer than the crown stock available, you need to splice (or scarf) two lengths together. Rather than attempt to fashion a good fit on the wall, I create my scarf joints first. For scarf joints, I depend on two critical devices: a biscuit and a splint. I begin by cutting a 20° bevel and a 20° miter—or 20/20 compound cut—on one end, an...
- Clayton Dekorne
Apr 26, 2018 · Traditional Issue 17 — Pre Season. Remodeling 101: What Is Crown Molding? Plus, What You Need to Know. by Barbara Peck Published: April 26, 2018. Many of us spend our days surrounded by molding, the trim often used around windows, doors, and ceilings in interiors. But how much time do we spend thinking about it? Precious little, right?
- Barbara Peck
Jan 7, 2019 · With the window crown molding and other parts cut to rough length, and the reveals marked on the jambs, the fastest and most accurate method for marking the trim for cutting is to simply hold the molding in place and mark it. It’s foolproof.
Overview. How To & DIY. Ideas & Inspiration. Installation. Video. All About Crown Molding. Highlighting the transition between walls and ceiling, this decorative trim adds character to even the plainest rooms. by Sal Vaglica, Contributor. In the world of trim, crown is king.
Mar 9, 2020 · Holding the crown down below the ceiling a bit (around 1/2”) allows you to keep the crown molding level around the entire room. And that means no tricky compound angles to cut (Garrett will explain that more in the video). Using level, flat crown also means that the gap between the crown and ceiling will change if your ceilings are uneven.
