Search results
Mar 26, 2015 · That will be a limiting factor. If the water is hot enough to mix significant cold water, then the cold pipe will carry part of the water. Now you may have to have a mixing valve to limit the temperature out of the spout. But if you must have a thermostatic mixing valve, you could put a thermostatic mixing valve at the bathroom fed by 150 ...
- Slip-On Spouts
- Threaded Spouts
- Tub Spouts with Brass Adapters - Threaded Or Slip-On
A slip-on style bathtub spout will have a setscrew, which is a small screw located on the bottom of the tub spout. The slip-fit tub spout is designed to slip onto a 1/2" copper pipewithout the use of any threads. The end of the copper that will be used must be free of burrs or rough edges, when using this type of spout.
A threadedtub spout will not have a setscrew, and will twist off of the nipple or pipe. This style will either be a front-end threaded tub spout or a rear-end threaded tub spout. 1. A front end threaded tub spout can be used with either a tub valve without a shower, or with a tub valve that has a shower diverter built into the tub valve. 2. The wal...
Some tub spouts may look like a threaded spout but in fact thread onto a brass adapter that is installed onto the pipe.There are two types of brass adapters, either a 1/2" IPS (iron pipe size) threaded adapter or a 1/2" nominal inside diameter (CTS) slip-on adapter, depending on the type of tub spout originally pur...The 1/2" IPS threaded adapter can be threaded onto galvanized, brass, stainless steel and other pipes with NPT (National Pipe Thread Taper) threads. These particular adapters can also be used on co...The 1/2" nominal inside diameter (CTS) slip-on adapter slides over the copper tubing and is secured to the copper pipe by tightening the set screw, or can be sweat/soldered to the pipe.Feb 1, 2024 · The answer the copper tub spout should be about 4 inches above the tub deck. Now here’s the deal, The Delta shower valve with the copper tub spout pre-installed makes this easy. I place my tape measure on the tub deck. Raise the copper tub spout to 4 inches. And there you go, that’s the proper height of the valve.
Oct 30, 2020 · Plumbing grease. How to Replace a Tub Spout. STEP 1. Scrape off old caulk. If there was a gap between the old spout and the wall, the new spout will eliminate it. STEP 2. Insert a large...
The tub spout is to be no less than 6 inches and no greater than 11 inches below the valve. If installing a threaded tub spout, connect to the valve with 1/2 inch pipe or 1/2 inch copper tubing with a threaded adapter. If installing a slip-fit tub spout, connect to the valve with only copper tubing – no threaded adapter is needed.
People also ask
How do I install a tub spout?
How high should a tub spout outlet be?
How much gap does a tub spout need?
What if a tub spout has no set screw?
installation (Cold water supply on the left and Hot water supply on the right), see Figure 3 and follow instructions a–d below: a. Connect cold inlet to hot port ("H") and hot inlet to cold port ("C"). NOTE: Do not turn valve upside down. If valve is upside down, water will not flow properly through tub spout or showerhead. b.
in-wall valves. Do not use hand showers connected in lieu of a tub spout to a tub/shower valve. Do not use PEX tubing for tub spout drop. Slip-On Installation The copper tube (1) must be 1/2” nominal copper. Important: If it is necessary to cut the copper tube, the end must be chamfered free of burrs to prevent cutting or nicking O-ring ...
